MechTech

@pengbuzz THE Masking Tape Master!!! @Cheese3 Cool to see those ole' tiny kits being built! I like the highlighting on the Defender. @woodsider That 1J looks beautiful! I think you'll win some medal with that one! ALCON - Here are International Plastic Modeler's Society (IPMS) judging guidelines (there is a Gundam section): - MT https://ipmsusa.org/about/competition-information/ipmsusa-competition-handbook-2024

@pengbuzz Your Shuttle looks GREAT! I love the protective coating on the lab module. It looks realistic! @Papa Rat No problem! Winning something at a con is cool too! Maybe fewer entrants? - MT

@Papa Rat Good call on the magnets for your Monster! By the way, if you're careful, they will still work just under the surface. That way you don't have to cover them with anything. Concerning your Talgeese: As a Sci-Fi judge for my club's last show, we dinged stuff like seam lines, rough paint, decals that were not blended well into the finish, or silvered decals (air gets underneath and it looks silvery). Stuff that will help you, adding detail bits, adding more scribing details/panel lines, and being consistent with your paint scheme (wear should be even across the model or rust, just not here and there). You should be able to get a a hold of the judging rules. If not, I'll see if I can find ours. Honestly, you should be able to walk into a show and have a good idea of where you stand. You know if you did a good job or not. At the very least, it's a lot of fun and a GREAT learning experience. You will see A LOT of awesome models and good ideas to borrow from. Who's hosting the show? If they are IPMS based, their rules are pretty much the same across the board. @Cheese3 Your paint shading looks good on that model and helps build size (for something so small). @derex3592 Good help is hard to find; I'm glad you got some! 😄 Sorry your Seymour-Johnson decal got jacked up. That squadron must of had a special deployment to Australia or something, maybe with a special paint scheme it sounds like? - MT

That's awesome she did that! I wanna say, "Sneaky wife, happy life" but that can go bad too.😁

@pengbuzz That's AWESOME man! Thank God for your wife and finding an ORIGINAL 80's kit! I remember that kit too - pretty cool! It's also great you got your starship nacelles sorted out too! Things are looking up! - MT

@Chas I think I used Super Lube (liquid) last time I stripped my old airbrush down. It has Teflon in it and coats nicely. @derex3592 Congrats on moving indoors! I lived in TX for a short bit and the heat and humidity can get bad! The Eagle looks good too! @Papa Rat Cool! Those will be a BIG improvement over the stock butcher block hands. - MT

@nightmareB4macross Thank you, but you're doing some awesome work! A lot of what I'm doing is because of the lathe and mill making up for my lack dexterity. GREAT detail work and funny pose for your not-so-Chunky Monkey. @Papa Rat Thank you! Congratulations on your anniversary! Doesn't seem that long! Are you making a glass cockpit for that VF-1 (another dad joke back at you)? For the Monster, you may want to look at some after market joints to put in that. The stock setup, while cool and articulated, just doesn't hold like Big S said. I checked USA Gundam Store and Newtype, but they are out of most of them right now. @Thom Thank you, Thom, I appreciate it! - MT

@Papa Rat That M.Lover looks GREAT! I love that Mr. Super Clear. It makes a lot of finishes just meld together. You're VF is coming along cool too! @nightmareB4macross Dude! Put your top back on, this is a family site!🤣 The Valk spread out reminds me of the old Imai cartoons where one of the girls has her Valks on display as insects with pins in them!😁 @Chas The paint looks SMOOTH on your SDF-1. The mods do too! ALRIGHT, so, my apologies for all the photos. I thought some of you might wonder how I did what I did and how it may help you (as I learn from you guys doing stuff too). Somebody I know wanted an F-35 for a temporary display. I mentioned I have an F-35B and they can borrow it after I build it. So I've been asked to build it, while forcing me to get it out of storage and building it. So, win-win! Back in 2018, I got the Hasegawa F-35B when it was new. Probably one of the best 1/72nd iterations of that airframe. Downsides, no ordnance and the decals are now outdated. The RAM tape that shows up as lighter colored lines all around the plane are now dated. It's all now the same color except for some hatches and stuff. The first thing people do when they look at an F-35B is look into the giant LiftFan behind the pilot. Hasegawa just has the top guard and a 1950's looking turbine blade under it, so I decided to make it more accurate. I think the F-35B is a cool plane design and I wanted to put the effort into it. The LiftFan has three sections you can see from the top. 1. The top guard with 11 spokes (and small sensor tubes all around). 2. Variable vanes that look similar to fan blades, but they're not. They're variable guides to adjust air flow. 3. The actual lift fan. In fact, there are two lift fans (counter-rotating) and other stators inside the fan housing, but you won't see them on the kit looking down, so I left them out here and on the model. First I tried making about seven turbine fans in styrene. All but one failed, and that one was shaped wrong, so I dropped that. This was about a week of wasted effort! So I'm showing you the bad with the good.😉 Next step was to build everything from soldered brass. That worked much better, but is A LOT more work. I used a pair of scissors and super-glued an angle piece onto it to act as a guide. - This is now how the "variable" vanes section went together: Then a depth gauge was used to keep the thicknesses the same when cutting all those tiny strips. Next, I needed a jig to hold the brass blades while soldering and doing other stuff, so I lathed and milled a block of bass wood. Next, all those little blades were sanded smooth to help with the finish and solder adhesion. Then the center piece was milled. This took a couple of tries. You can see there is hardly any material on the splines sticking up. This was the delicate part. They could easily break off - even in brass. The center piece and blades getting fit together. Then they were soldered. Note there is a slight angle to the left in the blades. - This is the top "Guard" piece. This is a similar piece, but it is for the guard that goes over the top. This is how I figured out how to shape it without busting up the delicate parts. The pieces stayed in the wood while I CAREFULLY sanded them to an angle. Soldered onto a piece of K&S metals tube. An iron was used because the mini-torch was too hot for this thin metal. And after A LOT of cleaning up, filing, and the center piece milled out... The top guard and vanes fit in place. The K&S tube was a God send, PERFECT fit after I cut out the center tub that came in the kit for the fan. The turbine center hub similar to above. This is also canted and tapered like the actual fan. The actual turbine was made similar to the vanes above. Just shorter, stockier blades. This is AFTER all the solder flux was cleaned off. I tried to think of how to put the twist in the blades. The answer was in front of me. I did opposite of the milling. I made a "reverse" screw driver blade with a taper. Then put it in the mill like I was going to make cuts. Instead, I manually twisted the bit just a little. Raised the bit, rotated the rotary table, lowered it onto another blade, and repeat - 24 times! I had to REALLY resist turning the motor on each time. This is similar to how I mill stuff in rotary increments. AND FINALLY, everything together. You can see Hasegawa's two pieces. Then (top right to lower left) came the LiftFan casing with the vanes in it, the top guard assembled, and the turbine - polished up and sized to fit inside the tube. The brass rod is the special tool used to twist the blades. It was fun, but A LOT of work to finally make a turbine. I'll have to remember this process for future models. Thanks for checking in! - MT

@GMK AWESOME sculpt and a radical looking design! - MT

@Papa Rat Nice fixes to the rear. By the way, use Milliput when it is still wet. It smooths down great with water and your fingers saving sanding, and trim it with blades while still semi-cured. It is good stuff. It just needs practice like any tool. @Urashiman Cool! Getting all electronicy too! I looked through my dad's old Lionel train stuff. There was this glob of aluminum with fins about the size of a small matchbox. I asked him what it was. He said, "A diode"! Technology sure has changed! 😁- MT

@Papa Rat Cool! I haven't built one of those in decades! Looking forward to it! @nightmareB4macross Thanks for sharing that! I forgot about that awkward designed head! - MT

@Cheese3 Your Misa figure looks good! I lost the eye decals for mine, so she came out looking more like Little Orphan Annie!🤣 @derex3592 Your work areas are looking great! Congrats! @Papa Rat The paint on your -1D looks REALLY good! Nice shading with the color mixtures. @Chas The mods to your SDF-1 made it look much better! @pengbuzz I saw a video online on how to save money model building. One of the suggestions was to use a watered down solution of white vinegar for a decal setting solution. I always thought setting solution smelled like acetic acid. I would give it a shot! - MT

@pengbuzz THANK YOU for the tip on the glue. I always thought it was the film that yellowed!? GREAT looking weathering and paint. I don't imagine they're the type of people to take their bird to the car wash!😁 - MT

@pengbuzz Thanks for the head's up Pengbuzz! Oh no! We finally "get back" a good stock of classic anime models and their company is not looking good. I've bought from them about three times now and no problem. I hope they're not folding 😕 @SteveTheFish Nice and clean paint! She looks good, especially with the patches as Chas said. - MT

@nightmareB4macross That will make a COOL diorama! @Thom GREAT cockpit detail! I'm glad to see a little known airframe get some love! @Chas Your updates are looking GOOD! I don't know the physical difference between the two (I haven't seen Hasegawa's in person), but I believe the most accurate SDF-1 is still the good ole Arii kit, and it could save you A LOT of hassle: https://www.ebay.com/itm/256534032075?_skw=sdf-1+macross&itmmeta=01JSY5XY2NVEGNBSNP5MRHMR0F&hash=item3bba9eaecb:g:owYAAOSwGvRmX3Ch&itmprp=enc%3AAQAKAAAA8FkggFvd1GGDu0w3yXCmi1c08UQTF0BSNandJSTeHQm7GfXKteB94MlA2SxKaFA72So0xVghBq5EjMQcjN94Y4XIeHn7A3JaPyTk3wrTszXaYsRYBmrt4GzRikbL4OfLrHGb%2FtuvnXWTg7GBjdE54zQqOs%2FnQGxX5nncTkx2H5vn4ukBAZC8k5K7ropAb1ewtBuQbspynLWWgZXR1EQejyaPPLPUAdtxccdOgFgrfBZCZX3y%2Fhqa6rICZ61%2BFDAWaLxyq8PHt8hcO1qevRFrrt1xm2M%2FDL2eDPhGBtC5UcqF09Gx6TH8QBH8hGLSikYhqw%3D%3D|tkp%3ABk9SR77h98XPZQ They're so inexpensive now, thanks to Wise Guys, (if you guys haven't shopped their ebay or web site, you're missing out) you can save a lot of trouble. I almost thought of using Hase's Daedalus and Promethius on the old Arii kit, but I don't know how far off they are. It would be nice to have the small vehicles that come with the Hasegawa kit - if they're to scale. - MT