asianLove Posted December 30, 2003 Share Posted December 30, 2003 (edited) Just for fun (and to test my building skills) I bought a cheap little 1/72 Itelari A-6 Skyhawk. Not a bad kit for 8 dollars. WeLL... I'm finding it REALLY hard to get the canopy to have that nice "glassy" look. Using 1500 grit "wet" paper. Is it just this hard with a cheap kit or would a vf-1 hasegawa kit be easier to sand and polish the canopy? What are some tips you guys can give for sanding and polishing a canopy? Oops.. sorry... this should be in the building section... Edited December 30, 2003 by asianLove Quote Link to comment Share on other sites More sharing options...
David Hingtgen Posted December 31, 2003 Share Posted December 31, 2003 (edited) 1500 isn't fine enough. Start going with 2000, 2500 for starters. That'll make it clear, and glossy enough for most thing. For REALLY crystal-clear, you'll want 4000 to 6000 grit. Also, do not "skip" grits. Use every grit possible. If you're using 1500, and have 4000, don't skip using the 2000. Use many "intermediate" grits between your first and final sanding. Finally, for canopies/polishing, I always sand dry. (The only time I wet-sand is for massive heavy mold-seams, like a 3-foot battleship's keel) Edited December 31, 2003 by David Hingtgen Quote Link to comment Share on other sites More sharing options...
Montarvillois Posted December 31, 2003 Share Posted December 31, 2003 Please don't laugh but toothpaste is the best canopy polisher you can find. It's a soft abrasive and it works much better on clear plastic than grit. Just pour a little bit on the caopy and use a clean cloth to rub the surface and then clean with water. I've tried it and it works wonders. Quote Link to comment Share on other sites More sharing options...
Vince Posted December 31, 2003 Share Posted December 31, 2003 The best result I've got so far is with Future. The most important thing is not to skip grit when using sand papers. However, there is no need to use anything higher than 2000 grit. When you are all done with sanding, rinse and dry the clear part then give it a short bath in Future Floor Polish. Wait at least an hour before touching or masking it. Apply micro polisher or rubbing compound at the end will make it even better. Of course, there is always scratch remover. Quote Link to comment Share on other sites More sharing options...
Pazu Posted December 31, 2003 Share Posted December 31, 2003 Ya. 1500 isn't nearly fine enuff. Use something more than that, I prefer to use my really worned sandpaper of fine grid. Wet sanding is not necessary. After that polish it will Plastic Liquid Polish like Novus Number 2 and finally (easiest part) coat it with future. Shiny canopy guaranteed! Pazu Quote Link to comment Share on other sites More sharing options...
dyowelb Posted December 31, 2003 Share Posted December 31, 2003 to remove the hazyness, use a rubbing compound and then soak it in a glass of Future floorwax.. Quote Link to comment Share on other sites More sharing options...
Myersjessee Posted December 31, 2003 Share Posted December 31, 2003 rubbing compound is what I go to also...which seems to do the trick. Quote Link to comment Share on other sites More sharing options...
asianLove Posted December 31, 2003 Author Share Posted December 31, 2003 Wow! COoL Tips! To Recap: Anything over 2000grit is too much. 1500grit isn't enough. After sanding, use some toothpaste, or rubbing compound. After toothpaste or rubbing compound, leave in "Future" for 1hr. What is rubbing compound? Future is a name brand floor-wax that can be bought at any supermarket, correct? Thanks for the GREAT suggestions! Sorry about posting in the wrong area. Quote Link to comment Share on other sites More sharing options...
dyowelb Posted December 31, 2003 Share Posted December 31, 2003 Wow! COoL Tips! To Recap:Anything over 2000grit is too much. 1500grit isn't enough. After sanding, use some toothpaste, or rubbing compound. After toothpaste or rubbing compound, leave in "Future" for 1hr. What is rubbing compound? Future is a name brand floor-wax that can be bought at any supermarket, correct? Thanks for the GREAT suggestions! Sorry about posting in the wrong area. no, 2000 grit is what you start with.. you can buy the rubbing compound thru your local hobby shop. you don't need to leave it in the floorwax, you just need to dip it... Quote Link to comment Share on other sites More sharing options...
Myersjessee Posted December 31, 2003 Share Posted December 31, 2003 Your local hobby store will most likely have several types of rubbing and polishing compounds...they range from a thick goo, to a thin goo, and have the slightest amount of grit in them, so as you rub them (with a cloth) on the canopy they will smooth out the ridges left from the sanding. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.