aurance Posted November 19, 2021 Share Posted November 19, 2021 (edited) Can anyone build for me that small grey cover? It doesn’t even need surface detail. Just to cover that gap behind the right leg. I will pay $50. Edited November 19, 2021 by aurance Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 19, 2021 Share Posted November 19, 2021 (edited) Let me take a look and see if I can do anything.... If possible, could you photograph the other leg cover detached, so I could get the tolerances on it? Edited November 19, 2021 by pengbuzz Quote Link to comment Share on other sites More sharing options...
aurance Posted November 19, 2021 Author Share Posted November 19, 2021 2 hours ago, pengbuzz said: Let me take a look and see if I can do anything.... If possible, could you photograph the other leg cover detached, so I could get the tolerances on it? I will try, it might be glued 😬 Quote Link to comment Share on other sites More sharing options...
aurance Posted November 19, 2021 Author Share Posted November 19, 2021 Yeah it’s stuck in there pretty good, I don’t think I can remove it without damaging it. ☹️ Maybe the other piece was missing out of the box and I just didn’t notice until now… Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 19, 2021 Share Posted November 19, 2021 Okay... let me see what I can do... Quote Link to comment Share on other sites More sharing options...
aurance Posted November 19, 2021 Author Share Posted November 19, 2021 56 minutes ago, pengbuzz said: Okay... let me see what I can do... Thanks pengbuzz 😊 Quote Link to comment Share on other sites More sharing options...
aurance Posted November 20, 2021 Author Share Posted November 20, 2021 Pics… Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 20, 2021 Share Posted November 20, 2021 (edited) 1 hour ago, aurance said: Pics… Thanks! I'll use these to start... I should have something to show you later tonight. Edited November 20, 2021 by pengbuzz Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 21, 2021 Share Posted November 21, 2021 Had a power outage tonight...hope to have progress tomorrow. Sorry. Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 21, 2021 Share Posted November 21, 2021 (edited) Okay, got some work done: It's upside-down right now, but I just have to cut the other end to shape and sand it. Stay tuned. Edited November 21, 2021 by pengbuzz Quote Link to comment Share on other sites More sharing options...
aurance Posted November 21, 2021 Author Share Posted November 21, 2021 You’re the best pengbuzz 🎉 Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 21, 2021 Share Posted November 21, 2021 1 minute ago, aurance said: You’re the best pengbuzz 🎉 Thanks; incoming PM for you with added details (realized I didn't want to say too much on the open boards). Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 22, 2021 Share Posted November 22, 2021 UPDATE: basic shaping finished- As soon as I refine the edges, I'll start the detail engraving. Then I'll work up the slightly smaller one. Stay tuned... Quote Link to comment Share on other sites More sharing options...
aurance Posted November 22, 2021 Author Share Posted November 22, 2021 You’re a true craftsman! Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted November 24, 2021 Share Posted November 24, 2021 update: Starting the smaller one (although I worry it may be a tad too small). I may do a third and just mail all three at this rate. Just want to get this right. Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted December 6, 2021 Share Posted December 6, 2021 Mission- Accomplished: Parts have been mailed out; one of these should fit! Quote Link to comment Share on other sites More sharing options...
aurance Posted December 13, 2021 Author Share Posted December 13, 2021 Public shoutout to pengbuzz again… second time you’ve rescued my valks from a sad life of staring at the wall in shame. 😝😝 Thank you for your craftsmanship and good humor! Quote Link to comment Share on other sites More sharing options...
pengbuzz Posted December 13, 2021 Share Posted December 13, 2021 1 hour ago, aurance said: Public shoutout to pengbuzz again… second time you’ve rescued my valks from a sad life of staring at the wall in shame. 😝😝 Thank you for your craftsmanship and good humor! My pleasure I'm just happy to help a fellow MW member in need! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.