Jump to content

Whats Lying on your Workbench MK IV


Urashiman

Recommended Posts

59 minutes ago, MechTech said:

Hi everyone, I got some more work done over the past couple of weekends. Sorry for photo-bombing you guys with so many photos!

The armored car I'm modifying is based on the French Panhard AML-90 (below). I modernized it a bit. You can see where the over-sized turret comes from.

35-109.jpg.1f0fb780f10e78fbc36c1556cb9873a5.jpg

Normal people remove screws from their tires and plug the hole. I punched a hole and glued some hanging out! These are what will hold the model to the base. I used silicone RTV to glue them in place.

35-110.jpg.d6942c6a6f11095287f6977814be3690.jpg

Here's the completed tires and base with screw heads underneath.

35-111.jpg.1d8e76972a33feca40412682e546b76f.jpg

35-112.jpg.4a334c253569c889765ef63a9c4728ed.jpg

I FINALLY got to put a base coat of paint on my model this weekend. Time for A LOT of weathering and detailing.

35-116.jpg.bfac29e7f5a72de1883cbf60543fecf8.jpg

Last weekend was spent doing landscaping on the base by adding more sand and more dead plant life. This was BEFORE I drilled the holes for the screws in the base. I also rusted parts from an old artillery carriage frame. I'm thinking of calling this diorama "The Sands of Time" or "Haunt of Jackals", but I'm not sure yet.

35-114.jpg.d63ce06bd5996d4993c6dc5bda1e8dfc.jpg

35-115.jpg.e931bd0a2bf6bd5a19481ef215c6fdad.jpg

35-113.jpg.a13a5781543665e639fd3604106f69ba.jpg

That's it for this time. Thanks for checking in everyone! - MT

 

Great work man!

Link to comment
Share on other sites

Okay, next phase on the F-5B cockpit section finished.

I’ll have to do a lot of sanding now, and then, the good old panel line scribing. YAY!

A bit better lighting today, so the “detail” is showing better.

87F1F3A1-F043-4ED9-BC72-8370BACB1C65.jpeg.768a0428b8f16da0abb95dab132254bb.jpeg
03EBCFD6-361D-4425-9916-82B87026E73E.jpeg.02a8f269d395fba1fa44fa53450787fe.jpeg

68397EA4-651B-4B47-9FBE-ED621420B5A4.jpeg.ed3ff22911c9a389b1fecb9518d79ddb.jpeg

1E019ECB-0123-4869-A177-8BBD2B99ACEB.jpeg.5b0a2a2f0a81f1c073364bb06baf19e5.jpeg

F1A6F0E7-2E1D-4C35-A852-7DB744D968F9.jpeg.916677fa1a8bff793f8a91feeabd266b.jpeg

Link to comment
Share on other sites

On 11/18/2021 at 5:05 PM, Thom said:

Dude, Perfect Plastic Putty!

I squeeze a bit out and apply with a toothpick along the seam or gap, and then wipe with a wet q-tip. Not meant for big gaps obviously, but for wing roots and such it is pretty perfect. And it's water-based, so just add more water to reactivate it.

Thanks @Thom  I'll have to try that out.

Link to comment
Share on other sites

Okay, update on the F5B.

I basically drenched it in Revell putty yesterday and let it dry for ~24 hours.

D535F72C-D9B1-42E1-8360-9C0CA3FDE735.jpeg.2eb5453778b9b0bc930d577c277400e7.jpeg

53C6716E-4C8F-4C11-9F82-F00C31D3D5DA.jpeg.7c4c8a148a5cdb291aeac5e30a0a0fdf.jpeg

and today I started to sand away on this like crazy. Uh!

D0B2F7A9-2369-4FD4-A415-698086C29BC3.jpeg.bc64132ea9e50c8feed87de00e80be09.jpeg
 

So this is where I am at now.

One side almost done, the other still needs so sandpaper love.

C6761A5A-AC22-4117-93A3-56CCEAF93739.jpeg.5d84a8b42b1449e01e250d408ee1a70f.jpeg
1CE8B7C1-1E36-42A8-963D-DFD9B082E430.jpeg.94211b2976dae6dd87827f25c04260d0.jpeg

I think I am on a good way here fixing this crappy kit. Lets see how it‘ll turn out.

Link to comment
Share on other sites

35 minutes ago, Urashiman said:

Okay, update on the F5B.

I basically drenched it in Revell putty yesterday and let it dry for ~24 hours.

D535F72C-D9B1-42E1-8360-9C0CA3FDE735.jpeg.2eb5453778b9b0bc930d577c277400e7.jpeg

53C6716E-4C8F-4C11-9F82-F00C31D3D5DA.jpeg.7c4c8a148a5cdb291aeac5e30a0a0fdf.jpeg

and today I started to sand away on this like crazy. Uh!

D0B2F7A9-2369-4FD4-A415-698086C29BC3.jpeg.bc64132ea9e50c8feed87de00e80be09.jpeg
 

So this is where I am at now.

One side almost done, the other still needs so sandpaper love.

C6761A5A-AC22-4117-93A3-56CCEAF93739.jpeg.5d84a8b42b1449e01e250d408ee1a70f.jpeg
1CE8B7C1-1E36-42A8-963D-DFD9B082E430.jpeg.94211b2976dae6dd87827f25c04260d0.jpeg

I think I am on a good way here fixing this crappy kit. Lets see how it‘ll turn out.

You're getting a GOOD workout sanding and a good looking fuselage too. -MT

Link to comment
Share on other sites

Well... I guess we're going to start 2022 a little early here-

 

I used High-Density Polystyrene (HDPS) that I culled from an old printer,to make the new wing attachment roots; thwe

100_0685.JPG.a10e353f2181a723a9212d37483909ad.JPG  

 

For the main joint, I got a piece of PVC tube and measured and cut it to the length of the entire joint (back interior wall to front interior wall). I then cut it in half and glued each half to a staggered set of wing roots:

100_0686.JPG.701cfdbebe47def58a823f1865269aed.JPG

 

The main pin is a hardwood dowel; this was chosen so that instead of splitting the tube (a real possibility, due to the fact that I had to cut slots in either side to accept the wing roots), it would compress instead:

100_0687.JPG.b690c2db3dbacc1f46e13ce5b43d032d.JPG  

 

Testing of the new pivot in "X" formation:

100_0688.JPG.ae82bad6d85023e1f127594245764c07.JPG

 

Testing of the new piece in both deployed and closed positions (sorry about the washed-out lighting):

100_0689.JPG.40e72a7ac07ac9992f638a3ad4c95b88.JPG   100_0690.JPG.eaf2c9e433a4a1ddb96d52408dd7a3f6.JPG

 

I then cut slots into the rear of the wing roots to properly mount the s-foils; I had to cut a sizeable chunk out of the area where the wing originally mounted and replace it with a better plastic:

100_0693.JPG.f05a8e27427495f2903c57e9ab80cdc8.JPG   100_0701.JPG.c5cd4ed21e70b49bd46107b9e38d5a47.JPG

 

Finally, finished:

100_0702.JPG.b10b5b3ff91e89050343f954e61a3552.JPG

The wings cant inward and downward slightly; that was unavoidable, given the work I had to do. The softness of the plastic determined for me that I had to male a few concessions in order to preserve the structural integrity of the craft as a whole. But, at least it's together now, and I'm sure the filming models weren't 100 percent perfect either!

Now: to get Darth's TIE X1 Advanced, and make a diorama...

Stay tuned.

Link to comment
Share on other sites

3 hours ago, Thom said:

@pengbuzz Nice save at the 2021 Buzzer! Just proves you can't keep a good modeller down!

@Urashiman Looking good! Now I can't wait to see the finish.

 

2 hours ago, MechTech said:

@pengbuzz GREAT save! That was an ingenious fix and creative with the materials too! The force is strong with this one!😁 Now you have a beautiful model for your collection. - MT

Thanks guys; still depressed about not scoring an SDF-1 and the other stuff, but ce la vie I suppose.

(la vie)

*ducks*

Now the next challenge: how to build a Death Star Trench Run diorama that isn't the size of a small room...

 

Link to comment
Share on other sites

 Hi All,

So I made this short build video for my new project, a platform deck add-on for my 1/72 Flight Deck.

It is not a public video, only you guys can see it.

I wanted to ask your opinions before I release it, whether you like this kind of thing, if the quality is good enough, and if I should make more throughout the project.  I'm not really into spending hours editing a professional video, but I can do something like this.

Edited by arbit
Link to comment
Share on other sites

5 hours ago, pengbuzz said:

Well... I guess we're going to start 2022 a little early here-

 

I used High-Density Polystyrene (HDPS) that I culled from an old printer,to make the new wing attachment roots; thwe

100_0685.JPG.a10e353f2181a723a9212d37483909ad.JPG  

 

For the main joint, I got a piece of PVC tube and measured and cut it to the length of the entire joint (back interior wall to front interior wall). I then cut it in half and glued each half to a staggered set of wing roots:

100_0686.JPG.701cfdbebe47def58a823f1865269aed.JPG

 

The main pin is a hardwood dowel; this was chosen so that instead of splitting the tube (a real possibility, due to the fact that I had to cut slots in either side to accept the wing roots), it would compress instead:

100_0687.JPG.b690c2db3dbacc1f46e13ce5b43d032d.JPG  

 

Testing of the new pivot in "X" formation:

100_0688.JPG.ae82bad6d85023e1f127594245764c07.JPG

 

Testing of the new piece in both deployed and closed positions (sorry about the washed-out lighting):

100_0689.JPG.40e72a7ac07ac9992f638a3ad4c95b88.JPG   100_0690.JPG.eaf2c9e433a4a1ddb96d52408dd7a3f6.JPG

 

I then cut slots into the rear of the wing roots to properly mount the s-foils; I had to cut a sizeable chunk out of the area where the wing originally mounted and replace it with a better plastic:

100_0693.JPG.f05a8e27427495f2903c57e9ab80cdc8.JPG   100_0701.JPG.c5cd4ed21e70b49bd46107b9e38d5a47.JPG

 

Finally, finished:

100_0702.JPG.b10b5b3ff91e89050343f954e61a3552.JPG

The wings cant inward and downward slightly; that was unavoidable, given the work I had to do. The softness of the plastic determined for me that I had to male a few concessions in order to preserve the structural integrity of the craft as a whole. But, at least it's together now, and I'm sure the filming models weren't 100 percent perfect either!

Now: to get Darth's TIE X1 Advanced, and make a diorama...

Stay tuned.

NIce!!!!!

Link to comment
Share on other sites

Agree! Great looking console @arbit

6 hours ago, pengbuzz said:

...Now the next challenge: how to build a Death Star Trench Run diorama that isn't the size of a small room...

 

1/144 scale, or is that still too big? Probably save space if you just do the floor and the 'back' wall.

Link to comment
Share on other sites

1 hour ago, MechTech said:

@arbit That's a cool idea! Just keep your work short and to the point. I see some videos and the dudes talk for like 10 minutes before they actually do anything. I look forward to your upcoming build! - MT

Thanks for the advice. So what ratio of my video was useless talking versus informative talking? Don't be shy, I need constructive criticism.

Of course, I will be actually building stuff and showing the project plan, this was just an off the cuff test of lighting, photography and audio.

Link to comment
Share on other sites

I felt, that I needed a break from the F-5B. So I started building something I have on my kit pile for years now.

 

128053ED-12F1-44E0-9328-90EE38CC0262.jpeg.37c1a01916ceac07d57863fd919f029d.jpeg

I got that VF-19A when it released the first time almost two decades ago. I also got the photo etched set from jasmine models, which is so awesome. I really like it.

Link to comment
Share on other sites

Putting my first HOUND together today. This is the first time I have ever built a kit made by WAVE, I must say I am very impressed of how every thing fits together, locks in places, only one little part was a royal pain otherwise a pleasure to build. B))

Painting & Decals to follow plus some pics. 

Fingers crossed a Hiro figure becomes available. 

 

IMG_2509.JPG

Edited by 505thAirborne
Link to comment
Share on other sites

Most of the assembly is done on my F-4J. It was going to be Showtime 100, but some hiccups in construction made me alter that.  Also got the Finemolds F-4J kit and it has markings for the Freelancers, so I'll be trading those out and saving Showtime 100 for another build. 

As it sits now.

st5DRGn.jpg

And since I'm doing this in a GB that I'm going to miss the deadline on, I'm going to shift it to the side and go back to the F-14 GB and get it to the same level of construction before painting both.

Here's the progress so far on the Tomcat.

0YFLv01.jpg

 

Modelling on!

Link to comment
Share on other sites

@arbit The video was good. I would focus on speaking clearly with confidence, be precise / brief to the point, edit footage to keep it brief, and keep a sense of humor. And don't be afraid to be funny - BUT be yourself!;)

@electric indigo That cockpit looks great! You can never have enough Harriers!

@Urashiman Yes, mental health is important!😁 That is a great looking photoetch set!

@505thAirborne What series is that from? I'm not familiar with it?

@Thom Those ejection seat fixes look good! - MT

Link to comment
Share on other sites

IT‘S ALIVE!
 

Okay… I think the F-5B is alive and kicking again.

Still need some panel line scribing but, it looks okay now.

31440A50-75A2-40EF-9ABA-B5936ACCF8A8.jpeg.f3393d8bb8e9e83c67df682b2bad9217.jpeg

And because working on two kits is not enough, I started kit number three!

Maxs VF-22 from macross 7.

81EE7609-710A-4601-8114-0DBA12F73001.jpeg.483fb826181f1e01c01c3b5569208f09.jpeg

Link to comment
Share on other sites

@Urashiman   A YF-19 is always a good idea. Why build anything other than Macross anyway, right :D

@505thAirborne That bike looks so cool, I'm drooling. Wave does have good quality, I have enjoyed building a couple things by them. I also really like their plastic, it is totally different than other model brands. Kind of hefty.

And @Thom is building a Thomcat, go figure.

Link to comment
Share on other sites

@Thom Getting everything together right for the "D" model seems to be tough for some reason. Even some purpose built "D" model kits.

 

@Urashiman 1600144322_Johnny5.jpg.063e013981cd794361e91f251278e4ac.jpg

 

@505thAirborne Ah yes, "Venus Wars". I loved the organic looking vehicles from that in lineart I saw. I don't remember if I saw the movie or not. That is a COOL looking model kit! It almost looks like it would be a possibility today. - MT

Link to comment
Share on other sites

4 hours ago, Urashiman said:

@MechTech hahahahaha yeah!

@arbit indeed. But this time it is a VF19A.

 

who can guess the white one?

47160AE5-C88B-428B-ADFB-8BDECA7FF6F4.jpeg.90cb4881fce415de3fc926beca081e41.jpeg

Looking good.

 

X-29?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...