Jump to content
Jefuemon

How to make recessed verniers

Recommended Posts

Some of you (hopefully) noticed that I recently got the book VF Modeling Manual. In there, they give a description on how to do a recessed vernier for your 1/72 kit. As I am building an old Imai Gerwalk now, and trying to pep it up a bit, here's what I did to make the vernier.

Start by getting yourself some 5 mm plastic pipe. I'm using Tamiya. No special reason for it being clear, that's just what the hobby shop happened to have in stock.

post-12411-0-09658300-1365154068_thumb.jpg

Next, take the part you want, and drill a 5 mm hole (obviously, on the Hasegawa kits, just remove the original casted vernier area.

post-12411-0-56923100-1365154075_thumb.jpg

Cut a small piece of the rod. I did around 4 mm long. Then, smooth out the rough edge.

post-12411-0-71214900-1365154081_thumb.jpg

post-12411-0-53249300-1365154087_thumb.jpg

Now, here is where I'm deviating from the Modeling Manual plans, since I've got some extra parts from Jasmine Models lovely VF-1 PE set. I'm using the round pieces in the lower left. Glue the round piece onto one end of the short tube.

post-12411-0-43050200-1365154095_thumb.jpg

post-12411-0-08457800-1365154102_thumb.jpg

Draw a mark on the tube for how far you want to insert it into your kit. You only want to go 2 mm or so. Put it, and glue it.

post-12411-0-65731600-1365154115_thumb.jpg

Once the glue has set, trim off the excess, and sand it flat.

post-12411-0-16047500-1365154121_thumb.jpg

Put on the top piece, and you're finished! (actually, wait to do this until you've primed and painted. much easier to get the inside black with no cover)

post-12411-0-18860500-1365154126_thumb.jpg

Now, if you don't have the PE set, use a small disk of plaplate (5 mm, natch), and a small strip over the top of it. You'll also want to get a circle scribing template (probably around 6 mm) to go around the outside of the hole.

Share this post


Link to post
Share on other sites

Working with this, I've noticed a change to the plans. If you're putting these in place while the part is still in half, hold off on putting on the inner disk until after the pipe has been trimmed, puttied, and sanded. Easier to get all the dust junk out if it's an open tube.

Share this post


Link to post
Share on other sites

Thanks Jefumon

I'd actually love to see all of the books' tips and techniques implemented and kept online for other modelers to see. hell... it would be awesome to see individual ones not associated to the book be posted over time.

Share this post


Link to post
Share on other sites

I don't think these are verniers, but I could be wrong.

Anyway nice little tutorial!

Share this post


Link to post
Share on other sites

To be nitpicking, the vernier inside cup should be a round shape :p

Just kiddind. for 1/72, that's very good detail.

Share this post


Link to post
Share on other sites

I don't think these are verniers, but I could be wrong.

Anyway nice little tutorial!

vernier/burner, there's been a discussion about which is the proper translation.

So far, things have been working out pretty well. I'm confident enough to try this out on my next VF-1 kit when I get to it.

To be nitpicking, the vernier inside cup should be a round shape :p

Just kiddind. for 1/72, that's very good detail.

I know. My original thought was to drill out the area, put a little lump of epoxy putty on the inside, then form it into a cone shape with a wooden stick. Could probably work that way, but I'll let someone else experiment with that!

Share this post


Link to post
Share on other sites

Where the heck can I get a copy of that book? I am very intersted.

Cheers,

Brett

Share this post


Link to post
Share on other sites

I ordered mine from HLJ They are listed as backordered but they were able to obtain one within a couple of days when I ordered mine 2 weeks ago.

Share this post


Link to post
Share on other sites

Where the heck can I get a copy of that book? I am very intersted.

Cheers,

Brett

I put the ISBN at the start of my review. Take that in to your local bookstore, and see if they can order you a copy.

Share this post


Link to post
Share on other sites

I missed that book well not for long heh heh !!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...