Jump to content

TER-OR

Members
  • Posts

    50
  • Joined

  • Last visited

TER-OR's Achievements

ARMD Deck Swabber

ARMD Deck Swabber (2/15)

0

Reputation

  1. Sorry it took so long, volunteer work does... It took a bit of learning to get the vacuum casting process down, but once I figured it out, I was pulling void-free casts. When I'll get around to building my copy, I can't say.
  2. Hi, Guys. Sorry the canopy bits have taken so long. I really don't have time to do this stuff anymore, but I know it can make a very nice canopy. My buddy has the masters now, and will pour rubber. I've ordered fresh resin and we'll vacuum cast the frame, and ambient cast bucks for the vacform plastic. The clear glass will sit inside the frame and be easy to install. Then it's just a matter of doing a couple a night (letting them sit long enough to get nice and rigid before demolding). The image is an old image from the beginning of the buck and before polishing up the canopy frame (and thinning it a bit). I know I have more recent pictures but can't seem to find them....anyway - you can see how this will work.
  3. I'll pre-order two. See you at Wfest in two weeks!
  4. Pre-ordering at SSM is essentially a reservation. When they're available you'll be sent a message asking whether you still want them, and if so to complete the purchase process. You don't pay up-front at the pre-order time. It's pretty important to pre-order, though, so Zero has an idea how many to order. PS, I saw the bits this weekend and they keep looking better and better!
  5. Ah, mine's too far along to add the photoetch. I guess I'll just have to buy a second kit! http://www.flickr.com/photos/ter-or/sets/72157623373328365/ I'll add more photos this week, I hope to finish it soon.
  6. Looks like you're off to a great start!
  7. For the fans, once you've painted them metallic, here's a trick. Add some India Ink to Future - and brush it on, make sure to break any bubbles. Let it settle into the recesses, it will concentrate in the low areas and against raised details. It sucks down well. Then dullcoat. Ink glazing works for lots of stuff - like wheel wells - but remember it follows gravity, so you may need to tilt your parts if you want a shadow effect. http://www.flickr.com/photos/ter-or/3818873253/ http://www.flickr.com/photos/ter-or/220796...57603704701438/ http://www.flickr.com/photos/ter-or/202405...57603176270104/
  8. Testor's Dullcoat is much too aggressive. I greatly prefer PolyScale's Flat Clear, but you have to dilute it pretty well.
  9. It's called a cowling. It's a combination of the standard Tire Black paint, a dilute black ink wash and very light drybrushing. The HUD projector is painted chrome with clear green over. I still haven't found any HUD display panel treatment that looks better than leaving it clear, though.
  10. Hey guys, it's been a while but I finally finished another Macross model. I haven't written the article yet, but will do so once I'm back from the IPMS Nationals. Here's Hasegawa's very nice VF-0D kit. It's painted in Gunze-Sangyo and Tamiya WW2 US Navy colors - medium gray and medium blue shaded with Blue FS 15050 (Blue Angels Blue). The gray is shaded with a lighter tone and the blue is faded with a lighter blue in splotches on the upper surfaces to simulate uneven wear common on naval aircraft. I use a multi-pass shading technique trying to give wear and grime etc. The last pass is the base color again to "erase" the overdone weathering where necessary. It's a little overdone on anime planes, but I go with it... The bottles and gear wells are painted with white, then glazed with India Ink in Future - which sucks down into the recesses very nicely for a sharp but not stark delineation. Cockpit details are from an F-18E photoetch set, some gleaned and scratchbuilt details as well. The ordinance of course is from the VF-1 weapons set. See more images on my Flickr site: http://www.flickr.com/photos/ter-or/sets/72157621852173999/ I'll post better pictures of my QF-11 drone later - I need to crop them etc.
  11. Thanks for sharing - it's great to see the VF-0s out there - I think it's an attractive design, too.
  12. It's great to see another person back in the modeling fold. We have a nice finishing forum over at starshipmodeler.net Some of the guys here are also members there. Battle damage is really difficult to simulate well - but scorching and some "roughing-up" is certainly doable with a moto-tool and airbrush.
  13. The compressor above looks fine. I use this: http://www.amazon.com/Senco-PC1010-Compres...6592&sr=8-1 A Senco 1010, it's surprisingly quiet.
×
×
  • Create New...